TrueChartsClone/charts/enterprise/metallb-config/docs/setup-guide.md at e299e047bb80a697529664a66b4cf0341d2c62ef

4.6 KiB

Raw Blame History

title
MetalLB Basic Setup

The guide walks through a basic configuration of MetalLB for a single address pool on a layer 2 network. This will allow assigning different IP addresses by app.

:::warning

With MetalLB installed, apps will not be reachable using the integrated LoadBalancer. You cannot combine two different LoadBalancers in TrueNAS SCALE.

:::

Prerequisites

Add the Operators & Enterprise trains to your TrueCharts Catalog.

:::caution

Our customized version of MetalLB is only intended for use with other TrueCharts applications. Other catalogs will likely not support our MetalLB application. MetalLB could technically work with TrueNAS catalog apps if they used the LoadBalancer service, but they don't as they use NodePort instead. These atypical configurations aren't officially supported nor encouraged by TrueCharts.

:::

1. Install MetalLB Operator from Operators Train

Install metallb from operators train first. There is no config, so just hit save.

If you encounter an error upon install, run the following command as root from system settings -> shell and attempt the install again: k3s kubectl delete --grace-period 30 --v=4 -k https://github.com/truecharts/manifests/delete

If you previously had metallb installed and encounter an error, delete the old version, then run the above command before proceeding to install the metallb operator.

2. Set Address Pool & L2 Advertisement in MetalLB-Config

Install metallb-config from enterprise train and create a new entry under Configure IP Address Pools Object

Name: Enter a general name for this IP range. Something like apps or charts for this field is fine.
Auto Assign: if you want MetalLB Services to auto-assign IPs from the configured address pool without needing to specify per app. Recommendation is to keep this checked. You can still specify an IP for apps as needed (see step 3).

Create a single entry under Configure Address Pools

Address Pool Entry: Specify an IP range for MetalLB to assign IPs that is OUTSIDE your current DHCP range on your LAN. For example, if your DHCP range is 192.168.1.100-192.168.1.255, then your entry can be any range below 192.168.1.100. This entry can also be specified in CIDR format.

For users with VLANs or multiple subnets, you may create create additional address pool objects as needed.

Create a new entry under Configure L2 Advertisements.

Name: Enter a basic name for your layer 2 advertisement.
Address Pool Entry: This should match the name of the address pool created above (not the IP range itself).

:::info

Once installed, metallb-config will always show as Stopped.

:::

3. Optional: Specify IP Address per App or Service

With MetalLB installed, it's recommended (but optional) to specify IP addresses for your apps.

For each app, under Networking and Services, select LoadBalancer Service Type for the Main Service.

In the LoadBalancer IP field, specify an IP address that is within the MetalLB address pool that you configured. Apply the same IP address to the LoadBalancer IP field on other services within the app.

4. Disable SCALE's Default LoadBalancer

With MetalLB installed and configured, you must now disable SCALE's default LoadBalancer.

In the SCALE UI, under Apps > Settings > Advanced Settings

Uncheck Enable Integrated LoadBalancer.

This will trigger a restart of Kubernetes and all apps. After roughly 5-10 minutes, your apps will redeploy using the MetalLB-assigned IP addresses.

5. Verify IP Addresses Are Assigned

From your SCALE shell, run the command k3s kubectl get svc -A to verify the IP addresses assigned for each of your apps. The IPs will be listed under the EXTERNAL-IP column.

If you have an IP conflict with a previously assigned address it will show as <pending>.

You may need to do a system reboot as well to properly resolve the conflict.